Template

Installation of PE Pressure Sewer Pipe by HDD

by john smith, from the Community

This field checklist guides the installation of PE pressure sewer pipe using horizontal directional drilling. It covers onsite documentation and permits, daily plant checks, material specs (PN16, SDR11, PE100), service locating and minimum clearances to WSA standards, traffic management and environmental controls, drill rig setup within the construction impact zone, pipe laying requirements including minimum cover and tracer wire, drilling fluid management with HydroVac, reaming and pullback practices, and verification, testing, and sign-off. Designed to support safe, compliant water and wastewater sewer works.

With SafetyCulture you can

Digitize any process, procedure or policy

Eliminate mistakes made by paper-based processes

Create and share professional reports instantly

Confirm accountability and compliance with a digital log

With SafetyCulture you can

Digitize any process, procedure or policy

Eliminate mistakes made by paper-based processes

Create and share professional reports instantly

Confirm accountability and compliance with a digital log

About author

Community

This community page makes available free workplace checklists and templates created by other users within the SafetyCulture community. SafetyCulture has re-published this content and where possible, has credited the original author. SafetyCulture has not verified the accuracy, reliability or suitability of any community content. You agree that your use of any of this content is in accordance with SafetyCulture’s Terms and Conditions.

Template
Sewer Bypass Pipe Pressure Test
Use this sewer bypass pipe pressure test checklist to document project details, verify welds and testing assemblies, confirm gauge condition and calibration, and record nominal pipe size, main length, material, and target test pressure. Capture start and end pressure readings with photos, note test times, and assess whether the main holds 800 kPa for 15 minutes. Add comments and supporting photos, then certify results with signatures from the project engineer and contractor for water and sewer renewals.
by James Le, from the Community
Downloads: 10+
Get
Template
SMEC Sewer Inspection and Audit Form
Use this SMEC sewer inspection and audit form to document sewer construction and rehabilitation works. Record project details, confirm OHS compliance and PPE, assess trench excavation dimensions and safety, verify pipe laying alignment and materials, check embedment and compaction, validate backfill type and evidence, and inspect manholes and structures. Add photos and notes, track sections checked, and capture onsite verification for quality, safety, and compliance.
by James Sorraghan, from the Community
Downloads: 20+
Get
Template
JSA for Horizontal Directional Drilling
Ensure safe horizontal directional drilling with this Job Safety Analysis template. It guides crews through hazard identification, PPE checks, evacuation points, traffic and pedestrian management, and working near overhead and underground assets. Cover environmental controls, excavation and ground support, non destructive excavation, and tools, plant, and equipment requirements. Includes a Plant Operators Daily Safety Checklist and a Vehicle Safety Check with trailer assessment, service intervals, and fire extinguisher and first aid verification. Use alongside relevant SWMS for cable installation, boring and drilling, and general works.
by Ben Koutoukidis, from the Community
Downloads: 100+
Get
Template
Service Line Installation Audit Checklist 2018
This audit checklist supports safe, compliant gas service line installation work. It covers work zone setup and traffic control, flagging operations, PPE, excavation and trench safety, electrical safety, tool and equipment checks, DOT vehicle and load securement, ergonomics, hazmat handling, fire protection, environmental controls, and hazard communication. Technical sections address abandoning old services, pipe separation, new service installation requirements including depth, tracer wire, marker balls, warning tape, and sewer locate practices to prevent cross bores. It details meter and regulator set installation, pipe joining by electrofusion and socket fusion, mechanical fittings, pressure testing at 1.5 times MAOP with leak checks, tapping pipelines into service, corrosion control with anodes and exothermic welds, backfilling, and final documentation.
by Benjamin Rodgers, from the Community
Downloads: 0
Get

Installation of PE Pressure Sewer Pipe by HDD

About author

You might also like

Sewer Bypass Pipe Pressure Test

SMEC Sewer Inspection and Audit Form

JSA for Horizontal Directional Drilling

Service Line Installation Audit Checklist 2018

You might also like

Sewer Bypass Pipe Pressure Test

SMEC Sewer Inspection and Audit Form

JSA for Horizontal Directional Drilling

Service Line Installation Audit Checklist 2018