Template

CSR Party Wall Inspection

by Anthony Cregan, from the Community

20+

This CSR Party Wall inspection checklist guides site supervisors through verifying Gyprock party wall systems for compliance and fire performance. It covers H-Stud and J-Track placement, vertical and horizontal shaftliner installation, Bradford Rockwool cavity seals, clip and strap spacing, laminated 16mm Fyrchek layers, acceptable gaps and fire seal use, fixing patterns, and service penetration clearances. It includes checks for eaves and roof terminations, transitions to external wall systems, and confirms no openings breach the barrier. The form supports result grading and supervisor sign-off after rectification.

With SafetyCulture you can

Digitize any process, procedure or policy

Eliminate mistakes made by paper-based processes

Create and share professional reports instantly

Confirm accountability and compliance with a digital log

With SafetyCulture you can

Digitize any process, procedure or policy

Eliminate mistakes made by paper-based processes

Create and share professional reports instantly

Confirm accountability and compliance with a digital log

About author

Community

This community page makes available free workplace checklists and templates created by other users within the SafetyCulture community. SafetyCulture has re-published this content and where possible, has credited the original author. SafetyCulture has not verified the accuracy, reliability or suitability of any community content. You agree that your use of any of this content is in accordance with SafetyCulture’s Terms and Conditions.

Template
Firestop and Cavity Barrier Site Audit
Conduct a thorough inspection of firestops and cavity barriers across your project. This checklist covers continuity of horizontal and vertical cavity barriers; placement around openings such as doors, windows, extract fans, meter boxes, and service entries; requirements at upper floor zones, party walls, eaves, verges, ceilings, and attic rooms; spacing of vertical barriers; and installation of Flexi Fire Stops. It also addresses stepped party wall details, cement/gypsum board to party walls, timber blocking between trusses, and soffit fire breaks. Site readiness checks include compartment walls, temporary fire doors, lift shaft closures, removal of pressurized gas canisters, and clearing excess materials and debris to reduce fire risk.
by Sam Greenfield, from the Community
Downloads: 10+
Get
Template
Party Wall Drylining QA Checklist
This construction QA checklist supports inspection of party wall drylining for South Thamesmead Phase II. It guides supervisors and subcontractors through checks on bottom and deep tracks, stud spacing and deflection gaps, fire strips and mastic, identification of wall types and junctions, cavity insulation (including 35 kg/m3 mineral and APR insulation), and 90/120 minute fire-rated partitions. It includes verification of IR01/IR02/IR03 riser and smoke shaft walls, timber studs at door jambs, security mesh, screw spacing to a 300 mm maximum, service fixing plasterboard strips, and screed shutters. The checklist emphasizes use of British Gypsum materials, requires photo evidence for key steps, and confirms areas are left clean, with sign-offs from contractor and client.
by Ionuț Țuțuianu, from the Community
Downloads: 0
Get
Template
Party Wall Drylining QA Checklist South Thamesmead II
Quality assurance checklist for party wall drylining on South Thamesmead Phase II. Verify correct installation of bottom and deep tracks, deflection allowances, firestrips or mastic, and stud spacing. Check fixing plates, set-out compliance, party wall junctions, cavity insulation including APR and 35 kg per m3 mineral wool, and fire rated walls at 90 or 120 minutes. Identify IR01 to IR03 riser or smoke shaft wall types, timber studs to door jambs, security mesh, and screw spacing at 300 mm. Confirm service fixing plasterboard strips, screed shutters, use of British Gypsum materials, site cleanliness, and capture photo evidence and signatures.
by Ionuț Țuțuianu, from the Community
Downloads: 0
Get
Template
Y-Wall Sheathing Board QC Checklist
This quality control checklist supports the installation of Y-Wall sheathing boards on site. It guides teams to verify required 2 to 5 mm gaps with fire rated mastic to Y-Wall specifications, correct fixing patterns, and completion by elevation, level, and section. The form includes hold points for photo evidence of completed works, space for notes, and a final sign off signature to confirm due diligence. Use it to document issues, rectification, and inspection status for compliant, auditable building envelope works.
by Greg Beaver, from the Community
Downloads: 0
Get

CSR Party Wall Inspection

About author

You might also like

Firestop and Cavity Barrier Site Audit

Party Wall Drylining QA Checklist

Party Wall Drylining QA Checklist South Thamesmead II

Y-Wall Sheathing Board QC Checklist

You might also like

Firestop and Cavity Barrier Site Audit

Party Wall Drylining QA Checklist

Party Wall Drylining QA Checklist South Thamesmead II

Y-Wall Sheathing Board QC Checklist