Template

F00145-A X-Ray Record

by Charik Urencio, from the Community

This X-Ray Record template supports hourly verification of metal and foreign-object detection on food production lines. Record product details, best-before date, test times, and results for stainless 316 1mm, aluminum 8mm, glass 6mm, ceramic 8mm, wire 2mm, and rubber ball 3mm. Log operator initials and QA checks, isolate rejected product, recheck once, and document root cause if failures occur.

With SafetyCulture you can

Digitize any process, procedure or policy

Eliminate mistakes made by paper-based processes

Create and share professional reports instantly

Confirm accountability and compliance with a digital log

With SafetyCulture you can

Digitize any process, procedure or policy

Eliminate mistakes made by paper-based processes

Create and share professional reports instantly

Confirm accountability and compliance with a digital log

About author

Community

This community page makes available free workplace checklists and templates created by other users within the SafetyCulture community. SafetyCulture has re-published this content and where possible, has credited the original author. SafetyCulture has not verified the accuracy, reliability or suitability of any community content. You agree that your use of any of this content is in accordance with SafetyCulture’s Terms and Conditions.

Template
A2O Versapanel Board Quality Assurance
Use this checklist to verify compliant installation of A2O Versapanel boards. Confirm 10 mm board as per drawings, check fixing centers at 600 mm horizontal, 300 mm vertical on board edges and 600 mm vertical in the center, with fixings at least 40 mm down and 15 mm in from edges. Leave a 3 to 6 mm gap and seal joints with versasealer. Provide 25 mm movement joints at slab level. Add photos, notes, and corrective actions, capture installer, contractor, and client signatures, and export the report.
by William Carter, from the Community
Downloads: 0
Get
Template
X-Ray FAT Checklist
This X-Ray Factory Acceptance Test checklist helps validate equipment before shipment. Verify model and serial labeling, required line items and accessories, sanitary design features, and safety devices including magnetic interlocks. Confirm OPC UA and I O units, RJ-IF connections, and infeed guides. Check radiation safety compliance, test pieces from 0.7 mm to 1.5 mm stainless steel, and document the machine setup with photos. Record SOP demonstrations, note follow up actions, and determine equipment readiness for dispatch.
by Nehemiah White, from the Community
Downloads: 0
Get
Template
Area MM Store Walkthrough
Area MM Store Walkthrough
by Mikey Murray, from the Community
Downloads: 30+
Get
Template
Y-Wall Board Quality Assurance Checklist
Ensure correct installation of Y-Wall sheathing boards with a focused QA checklist. Verify screw edge distances of 12 to 15 mm around perimeters, fixing spacing no greater than 300 mm vertically and 600 mm horizontally, and corner fixings 50 mm from edges. Confirm application of fire rated sealant and tape to all board edges, maintain 2 to 5 mm gaps between boards, and seal any additional penetrations. Capture site details, inspector, date, and complete A2O representative sign off. Designed to support consistent on site quality checks; always confirm requirements against the latest fixing schedule and project specifications.
by Aurelijus Juodelis, from the Community
Downloads: 0
Get

A2O Versapanel Board Quality Assurance

Use this checklist to verify compliant installation of A2O Versapanel boards. Confirm 10 mm board as per drawings, check fixing centers at 600 mm horizontal, 300 mm vertical on board edges and 600 mm vertical in the center, with fixings at least 40 mm down and 15 mm in from edges. Leave a 3 to 6 mm gap and seal joints with versasealer. Provide 25 mm movement joints at slab level. Add photos, notes, and corrective actions, capture installer, contractor, and client signatures, and export the report.

by William Carter, from the Community

Get

Template

X-Ray FAT Checklist

This X-Ray Factory Acceptance Test checklist helps validate equipment before shipment. Verify model and serial labeling, required line items and accessories, sanitary design features, and safety devices including magnetic interlocks. Confirm OPC UA and I O units, RJ-IF connections, and infeed guides. Check radiation safety compliance, test pieces from 0.7 mm to 1.5 mm stainless steel, and document the machine setup with photos. Record SOP demonstrations, note follow up actions, and determine equipment readiness for dispatch.

by Nehemiah White, from the Community

Get

Template

Area MM Store Walkthrough

by Mikey Murray, from the Community

30+

Get

Template

Y-Wall Board Quality Assurance Checklist

Ensure correct installation of Y-Wall sheathing boards with a focused QA checklist. Verify screw edge distances of 12 to 15 mm around perimeters, fixing spacing no greater than 300 mm vertically and 600 mm horizontally, and corner fixings 50 mm from edges. Confirm application of fire rated sealant and tape to all board edges, maintain 2 to 5 mm gaps between boards, and seal any additional penetrations. Capture site details, inspector, date, and complete A2O representative sign off. Designed to support consistent on site quality checks; always confirm requirements against the latest fixing schedule and project specifications.

by Aurelijus Juodelis, from the Community

Get

F00145-A X-Ray Record

About author

You might also like

A2O Versapanel Board Quality Assurance

X-Ray FAT Checklist

Area MM Store Walkthrough

Y-Wall Board Quality Assurance Checklist

You might also like

A2O Versapanel Board Quality Assurance

X-Ray FAT Checklist

Area MM Store Walkthrough

Y-Wall Board Quality Assurance Checklist