Template

Centrifuge Maintenance Checklist for Shops

by Lewis Rig 10, from the Community

Use this shop-based centrifuge maintenance checklist to document inspections, servicing, and test runs for oil and gas centrifuges. Cover safety checks, belts and guards, bearings and lubrication, gearboxes and clutches, electrical wiring and controls, vibration monitoring, and runtime readings, with photo evidence and notes to support reliable performance.

With SafetyCulture you can

Digitize any process, procedure or policy

Eliminate mistakes made by paper-based processes

Create and share professional reports instantly

Confirm accountability and compliance with a digital log

With SafetyCulture you can

Digitize any process, procedure or policy

Eliminate mistakes made by paper-based processes

Create and share professional reports instantly

Confirm accountability and compliance with a digital log

About author

Community

This community page makes available free workplace checklists and templates created by other users within the SafetyCulture community. SafetyCulture has re-published this content and where possible, has credited the original author. SafetyCulture has not verified the accuracy, reliability or suitability of any community content. You agree that your use of any of this content is in accordance with SafetyCulture’s Terms and Conditions.

Template
Terra Centrifuge Commissioning Checklist 2.1
This commissioning checklist helps supervisors verify the safe setup and operation of a Terra centrifuge system before start‑up on rig sites. It covers paperwork and readiness (JSA, risk assessment, DOR, AFE), installation checks, hazard mitigation, electrical grounding, and equipment placement. Detailed sections guide inspections of the drying shaker, feed and discharge augers, pumps, dryer, centrifuge stand safety devices, and centrifuge wear items and settings. It also includes inventory checks for screens and chemicals, toolbox readiness, and liability mitigation steps, with prompts for photos and notes to document findings.
by Drew Bollich, from the Community
Downloads: 20+
Get
Template
Annual Centrifuge Service Competency Evaluation
This competency evaluation checklist verifies an employee or contractor’s ability to service a centrifuge safely and effectively in oil and gas operations. It guides assessors through pre-job risk assessment and walk-around, equipment isolation with lock out tag out, inspection of rails, welds, hoses, piping, and case, cleaning of feed zones and gaskets, lubrication of bearings and couplers, gearbox oil checks, fastener verification, reassembly, start-up checks, and functional testing. It concludes with documentation and supervisor notification to confirm competency to the BOS Centrifuge Service SOP.
by Gary Bonnett, from the Community
Downloads: 0
Get
Template
Terra Centrifuge Inspection Report v01
This Terra Centrifuge Inspection Report v01 is a detailed checklist for commissioning and routine inspections of rig-mounted centrifuge units. It covers equipment installation checks, grounding and electrical safety, and pollution pan placement. Dedicated sections guide cleaning and exterior inspections for multiple centrifuges, including coffin lid condition, bolt integrity, belt guards, and BICC connections. Wear items such as feed tubes, plows or wear inserts, end wear plates, and solids wear liners are measured and photographed to verify condition. Operational settings are validated, including pond depths set to 7–7.5, proper belt speed configuration, and rotation checks. The form captures operator, rig, well number, and auditor details, and prompts photo evidence from multiple angles to ensure compliance and traceability.
by Drew Bollich, from the Community
Downloads: 20+
Get
Template
Stallion Centrifuge Commissioning Report
Use this supervisor-led commissioning report to document Stallion centrifuge setup on drilling rigs. Capture paperwork checks such as JSA and risk assessments; verify safe hose routing, cable management, and grounding; inspect BICC connectors, drying shakers and screens, centrifuge stands, and wear liners. Record feed pump wiring and rotation, overall rig-up photos, and third-party equipment for liability mitigation.
by Robert Domingue, from the Community
Downloads: 20+
Get

Terra Centrifuge Commissioning Checklist 2.1

This commissioning checklist helps supervisors verify the safe setup and operation of a Terra centrifuge system before start‑up on rig sites. It covers paperwork and readiness (JSA, risk assessment, DOR, AFE), installation checks, hazard mitigation, electrical grounding, and equipment placement. Detailed sections guide inspections of the drying shaker, feed and discharge augers, pumps, dryer, centrifuge stand safety devices, and centrifuge wear items and settings. It also includes inventory checks for screens and chemicals, toolbox readiness, and liability mitigation steps, with prompts for photos and notes to document findings.

by Drew Bollich, from the Community

20+

Get

Template

Annual Centrifuge Service Competency Evaluation

This competency evaluation checklist verifies an employee or contractor’s ability to service a centrifuge safely and effectively in oil and gas operations. It guides assessors through pre-job risk assessment and walk-around, equipment isolation with lock out tag out, inspection of rails, welds, hoses, piping, and case, cleaning of feed zones and gaskets, lubrication of bearings and couplers, gearbox oil checks, fastener verification, reassembly, start-up checks, and functional testing. It concludes with documentation and supervisor notification to confirm competency to the BOS Centrifuge Service SOP.

by Gary Bonnett, from the Community

Get

Template

Terra Centrifuge Inspection Report v01

This Terra Centrifuge Inspection Report v01 is a detailed checklist for commissioning and routine inspections of rig-mounted centrifuge units. It covers equipment installation checks, grounding and electrical safety, and pollution pan placement. Dedicated sections guide cleaning and exterior inspections for multiple centrifuges, including coffin lid condition, bolt integrity, belt guards, and BICC connections. Wear items such as feed tubes, plows or wear inserts, end wear plates, and solids wear liners are measured and photographed to verify condition. Operational settings are validated, including pond depths set to 7–7.5, proper belt speed configuration, and rotation checks. The form captures operator, rig, well number, and auditor details, and prompts photo evidence from multiple angles to ensure compliance and traceability.

by Drew Bollich, from the Community

20+

Get

Template

Stallion Centrifuge Commissioning Report

Use this supervisor-led commissioning report to document Stallion centrifuge setup on drilling rigs. Capture paperwork checks such as JSA and risk assessments; verify safe hose routing, cable management, and grounding; inspect BICC connectors, drying shakers and screens, centrifuge stands, and wear liners. Record feed pump wiring and rotation, overall rig-up photos, and third-party equipment for liability mitigation.

by Robert Domingue, from the Community

20+

Get

Centrifuge Maintenance Checklist for Shops

About author

You might also like

Terra Centrifuge Commissioning Checklist 2.1

Annual Centrifuge Service Competency Evaluation

Terra Centrifuge Inspection Report v01

Stallion Centrifuge Commissioning Report

You might also like

Terra Centrifuge Commissioning Checklist 2.1

Annual Centrifuge Service Competency Evaluation

Terra Centrifuge Inspection Report v01

Stallion Centrifuge Commissioning Report