Template

Cassette Panels to Composite Carrier: QA Checklist

by Lucian Galan, from the Community

Use this quality assurance checklist to guide the installation of Kingspan cassette panels onto composite carrier panels. It covers datum verification, level checks, vertical and horizontal module layout, support rail and clip installation, EPDM isolators, alignment, fixing patterns, security screws, and mullion gaps. Capture photos and notes, assign corrective actions, and complete installer, ICS, and client sign-off. Export reports in PDF, Word, Excel, or web link.

With SafetyCulture you can

Digitize any process, procedure or policy

Eliminate mistakes made by paper-based processes

Create and share professional reports instantly

Confirm accountability and compliance with a digital log

With SafetyCulture you can

Digitize any process, procedure or policy

Eliminate mistakes made by paper-based processes

Create and share professional reports instantly

Confirm accountability and compliance with a digital log

About author

Community

This community page makes available free workplace checklists and templates created by other users within the SafetyCulture community. SafetyCulture has re-published this content and where possible, has credited the original author. SafetyCulture has not verified the accuracy, reliability or suitability of any community content. You agree that your use of any of this content is in accordance with SafetyCulture’s Terms and Conditions .

Template

ICS Roofing: Composite Wall Panels QA Checklist

This ICS Roofing quality assurance checklist supports the installation of Euroclad composite wall panels. It covers pre-start checks (steelwork tolerances, drawings, and deliveries), primary seals and air/tape installation, panel engagement and horizontal joint alignment, correct fixings, lining and levelling, and flashing/secondary seal requirements. The template also enables photos, notes, corrective actions with assignees and due dates, and digital signatures for both ICS and client sign-off. It is intended as a practical guide for contractors and installers to document compliance and workmanship during panel installation.

by Lucian Galan, from the Community

Get

Template

ICS Composite Panels Quality Assurance Checklist

This ICS checklist supports quality assurance for Eurobond composite panels during construction. It guides installers through pre-install checks and installation verification, including steelwork tolerances, structural fixings, primary seals, and continuous rubber air seals. It covers panel condition, joint alignment, removal of protective film, and correct packing of gaps with rockwool or fire-rated foam. Flashings and secondary seals are detailed, with requirements for drip cover flashings, butt straps, butyl tape application, and fastener types. The workflow includes adding notes, photos, and actions, with installer, ICS, and client sign-offs to complete QA documentation.

by Lucian Galan, from the Community

Get

Template

Composite Panel Quality Inspection Checklist

Use this weekly composite panel quality inspection checklist to assess substrate condition and approvals, carrier system brackets and rails, cavity barrier placement and gaps, insulation layout and fixings, facade system specifications and edge distances, and flashings. Capture photos, note defects, and record sign-off to maintain installation quality and compliance on site.

by Steven McCrory, from the Community

Get

Template

Composite Roof Quality Assurance Checklist

Use this A2O composite roof quality assurance checklist to standardize installation checks from storage to final sign off. Verify mastic bead placement at eaves and ridge, adequate end lap bearing, side lap sealing and stitching, primary fixing counts, and ridge flashing laps with butyl mastic. Record findings with photos and notes, raise corrective actions with assignees, priorities, and due dates, then capture digital signatures from installer, A2O, and client. Export your completed report as PDF, Word, Excel, or share via web link.

by William Carter, from the Community

Get

Template

Handover Form for Composite Panels

This construction handover checklist is designed for composite panel installations on walls and roofs. It guides final quality checks on panel support and steel, correct tapes and sealants, panel line and level, fixings to specified centres per ICS CI drawings, flashing alignment, and overall cleanliness. The form captures project details (client, contract number, building/area, site, preparer, location) and includes sign-off sections for the installer (ICS Roofing Ltd) and the main contractor with names, signatures, and dates.

by Lucian Galan, from the Community

Get

Template

ICS Roofing Composite Panels Handover Form

Use this ICS Roofing handover checklist to complete and document final checks for composite panel roofing installations. Record project and site details, confirm panel supports and steels, verify tapes and sealants, ensure panels are aligned and level, and check fixings at the correct centres per ICS CI drawings. Review flashings for alignment, and confirm walls are clean and damage free. Capture inspection names, signatures, and dates for both ICS Roofing Ltd and the main contractor to formalise handover and close out.

by Lucian Galan, from the Community

Get