Template

RCD Replacement or Upgrade Method of Procedure

by David Sharp, from the Community

20+

This method of procedure guides electricians through replacing or upgrading RCDs and RCBOs in NBN node cabinets, including CommScope and Nokia variants. It details HSE and SWMS requirements, confirming backup supply, isolating power, installing approved RCBOs, and performing tests per AS/NZS 3000 and 3017. The process covers documentation such as Certificates of Electrical Safety, updating single line diagrams, and submitting artefacts like photographs and readings. Technicians record start-up and running currents, voltages, and site observations to ensure compliance and service continuity.

With SafetyCulture you can

Digitize any process, procedure or policy

Eliminate mistakes made by paper-based processes

Create and share professional reports instantly

Confirm accountability and compliance with a digital log

With SafetyCulture you can

Digitize any process, procedure or policy

Eliminate mistakes made by paper-based processes

Create and share professional reports instantly

Confirm accountability and compliance with a digital log

About author

Community

This community page makes available free workplace checklists and templates created by other users within the SafetyCulture community. SafetyCulture has re-published this content and where possible, has credited the original author. SafetyCulture has not verified the accuracy, reliability or suitability of any community content. You agree that your use of any of this content is in accordance with SafetyCulture’s Terms and Conditions .

Template
Service Stream NOC Method of Procedure
Use this Method of Procedure to manage WMC NOC service calls on FTTN network cabinets including CommScope, Nokia 384, and Nokia 192 CSD. It guides field electricians through site preparation, safety and HSE requirements, isolating supply, RCBO replacement, testing to AS NZS 3000 and 3017, and energizing. The checklist captures battery capacity checks, switchboard condition, measurements, artefact photos, certificates, and sign off to ensure safe, compliant, and consistent restoration of service.
by John Gillies, from the Community
Downloads: 20+
Get
Template
Install Replace and Test Electrical Safety Devices SWMS
This Safe Work Method Statement details the steps, hazards and control measures for installing, replacing and testing electrical safety devices in switchboards and on site. It includes risk assessment, isolation and lockout procedures, RCD trip time and push button testing, smoke alarm inspection and replacement, PPE requirements, and tool and equipment checks. References include AS NZS 4836 and AS NZS 3017 and relevant regulations. Use this template to guide safe electrical work and document verification and sign off before commencing and on completion.
by Himayat Ali, from the Community
Downloads: 10+
Get
Template
SWMS Install or Replace and Test Electrical Safety Devices
This Safe Work Method Statement provides step by step guidance to install, replace, and test electrical safety devices such as RCDs and smoke alarms. It includes a Take 5 risk assessment, PPE requirements, isolating and locking out power, switchboard inspection, testing procedures and trip time recording, replacement steps for failed devices, reinstatement of covers and supply, and tool calibration checks. Controls address electrocution, arcing, manual handling, trip hazards, and ladder use, with references to AS/NZS 4836 and AS/NZS 3017. Verification and sign off are included.
by Kelly South, from the Community
Downloads: 20+
Get
Template
AJK Electrical Check Sheet
This AJK Electrical Check Sheet supports EICR testing, repairs, and electrical maintenance. It helps teams capture client and site details, work hours, cost codes, and materials, while detailing common electrical tasks such as replacing lights and switches, fitting RCBOs and RCDs, installing smoke and heat detectors, upgrading consumer units, and documenting shower circuits and pull switches. The form guides users to record test results, defects, replacements, and certification notes, aiding compliance with wiring regulations and creating a clear audit trail for site inspections and remedial work.
by A&J keith, from the Community
Downloads: 30+
Get

RCD Replacement or Upgrade Method of Procedure

About author

You might also like

Service Stream NOC Method of Procedure

Install Replace and Test Electrical Safety Devices SWMS

SWMS Install or Replace and Test Electrical Safety Devices

AJK Electrical Check Sheet

You might also like

Service Stream NOC Method of Procedure

Install Replace and Test Electrical Safety Devices SWMS

SWMS Install or Replace and Test Electrical Safety Devices

AJK Electrical Check Sheet