Template

A101.2 Stripp Foundation Floor Checklist

by Flip le Roux, from the Community

Use this A101.2 Stripp foundation floor checklist to guide onsite inspections of foundation slab preparation and pours. Verify pre-work readiness, site cleanliness, backfilling quality and compaction, slab thickening trench dimensions, and installation of services and sand blinding. Confirm DPC overlap, mesh and reinforcing placement, above/below DPC services, and concrete thickness, strength, levels, and finish. Includes housekeeping reminders, required PPE, and foreman and subcontractor approval sign-offs.

With SafetyCulture you can

Digitize any process, procedure or policy

Eliminate mistakes made by paper-based processes

Create and share professional reports instantly

Confirm accountability and compliance with a digital log

With SafetyCulture you can

Digitize any process, procedure or policy

Eliminate mistakes made by paper-based processes

Create and share professional reports instantly

Confirm accountability and compliance with a digital log

About author

Community

This community page makes available free workplace checklists and templates created by other users within the SafetyCulture community. SafetyCulture has re-published this content and where possible, has credited the original author. SafetyCulture has not verified the accuracy, reliability or suitability of any community content. You agree that your use of any of this content is in accordance with SafetyCulture’s Terms and Conditions.

Template
A101.1 Strip Footings Checklist
This A101.1 Strip Footings checklist helps construction teams verify critical steps before and during foundation work. It covers pre-work checks, site preparation, setting out reference pegs, trench widths and depths, steel reinforcement placement and spacing, inspections, concrete strength and finish, test cubes, and required approvals. Includes housekeeping, PPE, and safety file reminders, plus signature fields for engineer, inspector, subcontractor, and foreman.
by Flip le Roux, from the Community
Downloads: 0
Get
Template
Eden Building Foundation and Slab Inspection
This foundation and slab inspection checklist supports code enforcement and quality control for new builds. It verifies correct setout to plans and FFL, use and condition of damp-proof membrane, clean rebar, proper grade and placement, and correct thickening dimensions and locations. It covers ground beams, pads under SHS or point loads, mesh and chairs for adequate cover, plumbing stub-ups and sleeved drainage, reinforcement bends and clearances, and electrical rough-in including kitchen island. Optional Hotedge installation types and joinery rebates are checked against guides. Inspectors can capture photo evidence of non-compliance and record signatures from the building inspector and subcontractor.
by Alvid Kok, from the Community
Downloads: 0
Get
Template
Pre-Slab Pour Inspection Report MSN
Use this pre-slab pour inspection report to confirm site conditions and compliance before concrete placement. Check setbacks, excavation dimensions, compaction, vapour barrier installation and taping, reinforcement laps and cover, service penetrations, and proposed floor levels. Attach comments, photos, and signatures to document quality and meet building standards.
by Will McNaught, from the Community
Downloads: 0
Get
Template
Excavation and Concrete Foundations Checklist
This practical checklist supports teams performing excavation and concrete foundation works. It covers pre-start risk assessment, identification of existing services, excavation accuracy and formation bearing capacity, required shoring, blinding preparation, formwork alignment and propping, reinforcement placement and cover, positioning of cast-in items, concrete placement and leveling, slump tests and test cubes, curing and protection, formwork removal and backfilling, housekeeping for subsequent trades, and safeguarding hazards to ensure quality and safety on site.
by Steve Hickey, from the Community
Downloads: 20+
Get

A101.1 Strip Footings Checklist

This A101.1 Strip Footings checklist helps construction teams verify critical steps before and during foundation work. It covers pre-work checks, site preparation, setting out reference pegs, trench widths and depths, steel reinforcement placement and spacing, inspections, concrete strength and finish, test cubes, and required approvals. Includes housekeeping, PPE, and safety file reminders, plus signature fields for engineer, inspector, subcontractor, and foreman.

by Flip le Roux, from the Community

Get

Template

Eden Building Foundation and Slab Inspection

This foundation and slab inspection checklist supports code enforcement and quality control for new builds. It verifies correct setout to plans and FFL, use and condition of damp-proof membrane, clean rebar, proper grade and placement, and correct thickening dimensions and locations. It covers ground beams, pads under SHS or point loads, mesh and chairs for adequate cover, plumbing stub-ups and sleeved drainage, reinforcement bends and clearances, and electrical rough-in including kitchen island. Optional Hotedge installation types and joinery rebates are checked against guides. Inspectors can capture photo evidence of non-compliance and record signatures from the building inspector and subcontractor.

by Alvid Kok, from the Community

Get

Template

Pre-Slab Pour Inspection Report MSN

Use this pre-slab pour inspection report to confirm site conditions and compliance before concrete placement. Check setbacks, excavation dimensions, compaction, vapour barrier installation and taping, reinforcement laps and cover, service penetrations, and proposed floor levels. Attach comments, photos, and signatures to document quality and meet building standards.

by Will McNaught, from the Community

Get

Template

Excavation and Concrete Foundations Checklist

This practical checklist supports teams performing excavation and concrete foundation works. It covers pre-start risk assessment, identification of existing services, excavation accuracy and formation bearing capacity, required shoring, blinding preparation, formwork alignment and propping, reinforcement placement and cover, positioning of cast-in items, concrete placement and leveling, slump tests and test cubes, curing and protection, formwork removal and backfilling, housekeeping for subsequent trades, and safeguarding hazards to ensure quality and safety on site.

by Steve Hickey, from the Community

20+

Get

A101.2 Stripp Foundation Floor Checklist

About author

You might also like

A101.1 Strip Footings Checklist

Eden Building Foundation and Slab Inspection

Pre-Slab Pour Inspection Report MSN

Excavation and Concrete Foundations Checklist

You might also like

A101.1 Strip Footings Checklist

Eden Building Foundation and Slab Inspection

Pre-Slab Pour Inspection Report MSN

Excavation and Concrete Foundations Checklist