Template

WTS2 Pit Patroller Shift Checklist

by Nicholas Grange, from the Community

Use this WTS2 Pit Patroller Checklist to standardize shift inspections across open-pit operations. Verify load and dump location sizing and boundaries, windrows and delineation, dump markers, tray-up times, and surveyed static courses and intersections. Review ROM and crusher areas, paddock dumps, and reclaim space. Check access controls, signage, speed limits, and cab readiness. Capture comments and assign actions for any noncompliance to support safer operations and smoother handovers.

With SafetyCulture you can

Digitize any process, procedure or policy

Eliminate mistakes made by paper-based processes

Create and share professional reports instantly

Confirm accountability and compliance with a digital log

With SafetyCulture you can

Digitize any process, procedure or policy

Eliminate mistakes made by paper-based processes

Create and share professional reports instantly

Confirm accountability and compliance with a digital log

About author

Community

This community page makes available free workplace checklists and templates created by other users within the SafetyCulture community. SafetyCulture has re-published this content and where possible, has credited the original author. SafetyCulture has not verified the accuracy, reliability or suitability of any community content. You agree that your use of any of this content is in accordance with SafetyCulture’s Terms and Conditions.

Template
WTS2 Pit Patroller Checklist
Use this WTS2 Pit Patroller Checklist to guide shift inspections across the pit. Verify load and dump locations are sized and protected, check grader windrows, markers, and delineation, and confirm dump nodes and configurations meet standards. Review ROM and crusher areas, tray-up times, and PLOD movements. Inspect static courses and intersections, MWSL/LASL, AT access gates, and general pit conditions. Capture comments, assign actions for non-compliance, and support clear shift handovers.
by Dean Minoughan, from the Community
Downloads: 10+
Get
Template
General Open Pit Inspection Checklist
This general open pit inspection checklist helps mining supervisors and technical staff verify pit safety and compliance at key times, including the start of each shift, after blasting, and following major rain. It covers pit walls and berms, drill and blast controls, floors and hazardous areas, dumps and stockpiles, roads and ramps, signage, traffic management, drainage, windrows, and go-line conditions. Use it to identify hazards, confirm design compliance, and document corrective actions for safer open pit operations.
by Gregory Turner, from the Community
Downloads: 30+
Get
Template
Savage River Pit Inspection Checklist
Conduct comprehensive daily inspections across open-pit mine areas with this Savage River Pit checklist. Evaluate haul road conditions, drainage, signage and delineation, windrows and berms, dump stability, dig face heights and overhangs, intersections, sumps and pump access, ROM floor and access roads, and PPE readiness. Identify geotechnical risks, oversize material, vegetation hazards, and SOP compliance to maintain safe, efficient operations.
by John Fox, from the Community
Downloads: 0
Get
Template
Open Pit Mining Workplace Inspection Checklist
This open pit mining workplace inspection checklist helps teams verify safe, compliant operations across pits, ROM stockpiles, waste dumps, and haul roads. It guides checks on access control, road condition, camber and super-elevation, windrows and bunds, delineation, lighting, dust suppression, signage, and restricted areas. Inspectors confirm pit wall stability, batter angles, bench access, floor levels and gradients, pumping and water management to sumps, and communications or two-way network status. It also covers PPE use, incident and hazard reporting, facility cleanliness, fuel and go-line conditions, and crew readiness before work begins.
by Belinda Van der Merwe, from the Community
Downloads: 10+
Get

WTS2 Pit Patroller Checklist

Use this WTS2 Pit Patroller Checklist to guide shift inspections across the pit. Verify load and dump locations are sized and protected, check grader windrows, markers, and delineation, and confirm dump nodes and configurations meet standards. Review ROM and crusher areas, tray-up times, and PLOD movements. Inspect static courses and intersections, MWSL/LASL, AT access gates, and general pit conditions. Capture comments, assign actions for non-compliance, and support clear shift handovers.

by Dean Minoughan, from the Community

10+

Get

Template

General Open Pit Inspection Checklist

This general open pit inspection checklist helps mining supervisors and technical staff verify pit safety and compliance at key times, including the start of each shift, after blasting, and following major rain. It covers pit walls and berms, drill and blast controls, floors and hazardous areas, dumps and stockpiles, roads and ramps, signage, traffic management, drainage, windrows, and go-line conditions. Use it to identify hazards, confirm design compliance, and document corrective actions for safer open pit operations.

by Gregory Turner, from the Community

30+

Get

Template

Savage River Pit Inspection Checklist

Conduct comprehensive daily inspections across open-pit mine areas with this Savage River Pit checklist. Evaluate haul road conditions, drainage, signage and delineation, windrows and berms, dump stability, dig face heights and overhangs, intersections, sumps and pump access, ROM floor and access roads, and PPE readiness. Identify geotechnical risks, oversize material, vegetation hazards, and SOP compliance to maintain safe, efficient operations.

by John Fox, from the Community

Get

Template

Open Pit Mining Workplace Inspection Checklist

This open pit mining workplace inspection checklist helps teams verify safe, compliant operations across pits, ROM stockpiles, waste dumps, and haul roads. It guides checks on access control, road condition, camber and super-elevation, windrows and bunds, delineation, lighting, dust suppression, signage, and restricted areas. Inspectors confirm pit wall stability, batter angles, bench access, floor levels and gradients, pumping and water management to sumps, and communications or two-way network status. It also covers PPE use, incident and hazard reporting, facility cleanliness, fuel and go-line conditions, and crew readiness before work begins.

by Belinda Van der Merwe, from the Community

10+

Get

WTS2 Pit Patroller Shift Checklist

About author

You might also like

WTS2 Pit Patroller Checklist

General Open Pit Inspection Checklist

Savage River Pit Inspection Checklist

Open Pit Mining Workplace Inspection Checklist

You might also like

WTS2 Pit Patroller Checklist

General Open Pit Inspection Checklist

Savage River Pit Inspection Checklist

Open Pit Mining Workplace Inspection Checklist